Inside Door Handle Trim Removal.. - Printable Version +- FocusCanada Forums (//www.focuscanada.net/forum) +-- Forum: Technobabble (//www.focuscanada.net/forum/forumdisplay.php?fid=4) +--- Forum: Focus on Appearance (//www.focuscanada.net/forum/forumdisplay.php?fid=21) +--- Thread: Inside Door Handle Trim Removal.. (/showthread.php?tid=14191) |
Inside Door Handle Trim Removal.. - JRC ZX3 2003 - 07-14-2005 The plastic thats around the inside door handle to open the door has 1 screw in middle. I removed it and got it almost off, it looks stuck at where the switch is for the auto locks. Is there something im missing to remove it, also.. is the switch hard wired right in.. or is there male/female conectors? Anyone have any info would be great.. Wish i had a picture. Also, on the actually door handle, there is a small piece of trim in the middle, i can pop out 2 clips.. but its still stuck, and i dont want to break it.. how many clips am i looking for? thanks! Inside Door Handle Trim Removal.. - Oscar The Grouch - 07-14-2005 Actually, you can push that switch from the inside out. The cord should be long enough for good slack. Then what you have to do is disconnect the plug from the cable. on the plug there is a little slot clip, you might need a standard flathead screwdriver to help you get it off. There should be 3 clips in the trim piece around the door opening latch. As for the trim peice, there should be 3 clips as well, one on the top, one on the side and one near the door hinges. Basically you have to pry it from the bottom and it should pop out. I'll see if I can whip up some pics. Inside Door Handle Trim Removal.. - JRC ZX3 2003 - 07-14-2005 Oscar The Grouch,Jul 13 2005, 07:36 PM Wrote:Actually, you can push that switch from the inside out. The cord should be long enough for good slack. Then what you have to do is disconnect the plug from the cable. on the plug there is a little slot clip, you might need a standard flathead screwdriver to help you get it off. Pics would be awsome thanks. The trim piece has 2 clips on top, i know that for sure. Inside Door Handle Trim Removal.. - Oscar The Grouch - 07-14-2005 JRC ZX3 2003,Jul 13 2005, 07:39 PM Wrote:Oscar The Grouch,Jul 13 2005, 07:36 PM Wrote:Actually, you can push that switch from the inside out. The cord should be long enough for good slack. Then what you have to do is disconnect the plug from the cable. on the plug there is a little slot clip, you might need a standard flathead screwdriver to help you get it off. This should help big time. c/o focusfanatics.com Door Trim Removal Inside Door Handle Trim Removal.. - Oscar The Grouch - 07-14-2005 JRC ZX3 2003,Jul 13 2005, 07:39 PM Wrote:Oscar The Grouch,Jul 13 2005, 07:36 PM Wrote:Actually, you can push that switch from the inside out. The cord should be long enough for good slack. Then what you have to do is disconnect the plug from the cable. on the plug there is a little slot clip, you might need a standard flathead screwdriver to help you get it off. This should help big time. c/o focusfanatics.com Door Trim Removal This one too for the rear speakers: Rear Speakers in ZX3 Inside Door Handle Trim Removal.. - JRC ZX3 2003 - 07-14-2005 Oscar The Grouch,Jul 13 2005, 08:21 PM Wrote:JRC ZX3 2003,Jul 13 2005, 07:39 PM Wrote:Oscar The Grouch,Jul 13 2005, 07:36 PM Wrote:Actually, you can push that switch from the inside out. The cord should be long enough for good slack. Then what you have to do is disconnect the plug from the cable. on the plug there is a little slot clip, you might need a standard flathead screwdriver to help you get it off. Thanks for the link. That shows me how to solve 1 problem, it looks to me that the piece that has the power locks in it.. should just pop out.. im still wondering where i have to pry.. ill have to take another look at it tommorow. Inside Door Handle Trim Removal.. - Oscar The Grouch - 07-14-2005 JRC ZX3 2003,Jul 13 2005, 09:01 PM Wrote:Oscar The Grouch,Jul 13 2005, 08:21 PM Wrote:JRC ZX3 2003,Jul 13 2005, 07:39 PM Wrote:Oscar The Grouch,Jul 13 2005, 07:36 PM Wrote:Actually, you can push that switch from the inside out. The cord should be long enough for good slack. Then what you have to do is disconnect the plug from the cable. on the plug there is a little slot clip, you might need a standard flathead screwdriver to help you get it off. If you have probs, lemme know. I'll be heading to T.O. this weekend and can give ya a hand if ya need one. Inside Door Handle Trim Removal.. - JRC ZX3 2003 - 07-19-2005 Oscar The Grouch,Jul 14 2005, 07:50 AM Wrote:JRC ZX3 2003,Jul 13 2005, 09:01 PM Wrote:Oscar The Grouch,Jul 13 2005, 08:21 PM Wrote:JRC ZX3 2003,Jul 13 2005, 07:39 PM Wrote:Oscar The Grouch,Jul 13 2005, 07:36 PM Wrote:Actually, you can push that switch from the inside out. The cord should be long enough for good slack. Then what you have to do is disconnect the plug from the cable. on the plug there is a little slot clip, you might need a standard flathead screwdriver to help you get it off. Thanks for the offer. I got 1 of the 2 done. I just vinyl wraped them for now. Until i decide to actually paint. Still doesnt look 1/2 bad at the moment. Inside Door Handle Trim Removal.. - Oscar The Grouch - 07-19-2005 awesome. :D |