+- FocusCanada Forums (//www.focuscanada.net/forum)
+-- Forum: Technobabble (//www.focuscanada.net/forum/forumdisplay.php?fid=4)
+--- Forum: The Basics (//www.focuscanada.net/forum/forumdisplay.php?fid=25)
+--- Thread: Passenger Motor Mount done? (/showthread.php?tid=20811)
Passenger Motor Mount done? - reldridge - 10-22-2012
Getting some vibrations, and from what I've seen is that it could be motor mount related.
I grabbed a picture. Is this thing done? It's pretty 'concave' in the middle.
![[Image: focusmount.jpg]](http://i320.photobucket.com/albums/nn327/reldridge78/focusmount.jpg)
-Ryan
RE: Passenger Motor Mount done? - hardk0re - 10-22-2012
IIRC they always looked like that from what I recall.
RE: Passenger Motor Mount done? - GFXjamie - 10-23-2012
i thought they were more "inflated" looking
RE: Passenger Motor Mount done? - muttsnutts - 10-23-2012
I just changed mine It looked the same but was split underneath.
RE: Passenger Motor Mount done? - ZTWsquared - 10-23-2012
(10-23-2012, 12:21 AM)GFXjamie Wrote: i thought they were more "inflated" looking
^^^ I think Jamie's right - in any event, yours is missing the cap - here's what it should look like, and below that with the cap on:
![[Image: d03620f5-2e99-412e.jpg]](http://img.tapatalk.com/d03620f5-2e99-412e.jpg)
![[Image: zetecenginemount.jpg]](http://www.c-f-m.com/productimages/detail/zetecenginemount.jpg)
RE: Passenger Motor Mount done? - reldridge - 10-23-2012
Thanks Ken! Helpful as always.
I do have the cap, I just pulled it off for photo reasons.
RE: Passenger Motor Mount done? - sonic_mikey - 10-29-2012
Have any of them been removed lately for any type of work? miss aligned mounts can cause some vibration
RE: Passenger Motor Mount done? - stupica1 - 10-30-2012
I say just replace it anyways and call it a day. they're not overly expensive for a stock mount and takes 30 minutes to change. Just make sure they're torqued down properly and you're good to go.
RE: Passenger Motor Mount done? - muttsnutts - 10-30-2012
(10-30-2012, 01:33 AM)stupica1 Wrote: I say just replace it anyways and call it a day. they're not overly expensive for a stock mount and takes 30 minutes to change. Just make sure they're torqued down properly and you're good to go.
Agreed
RE: Passenger Motor Mount done? - heelchain - 03-18-2013
How did it work out Ryan? I am having some intermittent vibration issues while in gear but stopped at a light or in a parking lot about to back out of the spot. Big vibrations. other times it is just fine.
Cheers,
Scott
RE: Passenger Motor Mount done? - reldridge - 03-19-2013
I actually haven't touched it yet. It will be part of my Spring Renewal project...
RE: Passenger Motor Mount done? - drunkinmonkey - 03-19-2013
(03-19-2013, 12:45 AM)reldridge Wrote: I actually haven't touched it yet. It will be part of my Spring Renewal project...
i was getting some really bad vibration as well turns out it was the dogbone
RE: Passenger Motor Mount done? - dBlast - 03-19-2013
I recently replaced both upper mounts. Before I replaced them, there were noticable vibrations especially when there were dips in the road or anytime there was compression on the springs when turning. Now it drives like a new car!!