Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Pillar Tach Hookup Idea
#1
A while back, NOS4Me2go installed a cluster in his car with a tach in it. From what he said it was a simple install as all he had to do was just hook up the tach'd cluster and bolt it back in and bam...he had a tach.

Well this got me thinking. Obviously dispite the focus you got you had a tach signal on the harness for the cluster. I was wondering if it was possible to say tap into this wire and use an aftermarket tach on your car.

I bought a 2 guage pod cluster a pillar dealy, a 2" tach and a 2" volt meter.

Well any thoughts on this idea would be great. Also...if say it will work...which wire on the harness would be the tach sending signal?
Join the Sedan Faction - You know you want to.
Reply
#2
I think the difference is this is a digital gauge, one that is reading values from your computer and displaying them. So no an aftermarket tach won't work unless you get a tach driver. (well thats the easy way) I'm sure theres another way to do it thats cheaper but a little more complicated.
Reply
#3
ok I will just go the tach driver way. I just figured that you could tap off the signal on the cluster. Thats how my friend did it in his 1993 honda civic.
Join the Sedan Faction - You know you want to.
Reply
#4
Isn't there a pin on the ECU that you can tap and use without using a tach driver?
Current
09 F150 SCREW 4X4 XTR

Former
Show
Hella Magic Module Tail Lights, 17" Ford Racing EAP rims, 5% Rear, 20% Front Tint, Panasonic CQ7401 Deck, 2 MB Quart 10's, Alpine Components, Phoenix Gold 500.1 Amp
Go
Steeda Cold Ram Air Intake MBRP Exhaust (Gen 2), FK Coilovers, Hedman Header (Install Pending),FC Hi-Flo Cat (Install Pending),EBC Greenstuff Pads

Reply
#5
habmann,Apr 19 2006, 11:20 PM Wrote:Isn't there a pin on the ECU that you can tap and use without using a tach driver?
[right][snapback]182246[/snapback][/right]
Zetecs -- > Yes, ECU Pin 48 (if I recall correctly)

Duratecs -- > No. You need a tach driver. You cannot tap off a lead going to the cluster. The tach signal to the cluster with the Duratecs is a multiplexxed signal (CANBUSS); that is incorporated with a bunch of other signals that go to the cluster and are interpreted.

What you can do (and what I did) is wire the tach driver to the CPS signal at the ECU (inside the car) rather than at the CPS/COP itself (outside the car.)

I have a how-to over at FocusFanatics I can give you the link for if you need it.
TEAM PITA: Don't settle for a wannabe, only accept the real deal.
*Magnetic Metallic 2015 Focus ST* *Red Candy Metallic 2012 F150 SuperCrew*
*Supercharged Roush Phase 2 Kona Blue 2012 Mustang GT*
Reply
#6
What about SPI? Cuz thats what my car is packin'
Join the Sedan Faction - You know you want to.
Reply
#7
good luck! ^^
THE FOCUS IS GONE! THE LEGEND IS DEAD!

but hey, im still around.....
Reply
#8
The digital / analog thing might come into play. All SPIs are capable of using any N.A. Focus cluster that has a tachometer... this much I'm sure of now.

Also, according to the guys on FJ, the SPI is the same as the Zetec... pin #48 for the tach signal. I would imagine that's a digital signal coming from that wire, though. Not sure to be perfectly honest.
Daily driver 1: 2007 Jeep Wrangler Unlimited Sport "S"

33" BFG Mud-Terrain KM2s, lots of Rough Country gear - bumper, 2.5" lift, swaybar disconnects, Superwinch 10,000lb winch, Detroit Locker in rear D44 axle, custom exhaust, K+N filtercharger, Superchips-tuned.

Daily driver 2: 2006 Subaru Legacy GT

COBB Stage 1+ package - AccessPort tuner, COBB intake and airbox. Stage 2 coming shortly - COBB 3" AT stainless DP and race cat, custom 3" Magnaflow-based exhaust and Stage 2 COBB tune.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)