[2000zx3sct]

Mirrors , ebrake , steeda door sills , svt door sills ,

[2000zx3sct]

Steeda Sills , $50 Obo retail for around $120 . Been cut down to fit 4 door models

[2000zx3sct]

Also the interior is still up for grabs , seats front + back along with the door cards . Not much else that I can think of at the moment , have a black dash that I will be throwing away ,if someone wants it let me know. You can text me for a faster response 289-208-5361 I also updated the original list on the first page .

[2000zx3sct]

Updated the list

[2000zx3sct]

HMirrors sold , dash sold . I now have the following left over - two red door handles , Svt OEM subwoofer, Svt leather ebrake , two Svt door sills for zx5 , full leather interior - Svt seats front + back + door cards , 4 SVT speakers , SVT hatch spoiler , SVT header , Front Svt brake setup , Svt front + rear swaybars , SVT steering rack . Also just got a Silver Svt front bumper in that I'm willing to part with .

[2000zx3sct]

Adding a borla exhaust for Svt focus , 2.5 inch . Retails for $580 on CFM , asking $300 for focuscanada members

[rnzo86]

how much for the trunk trim ?

[2000zx3sct]

Keeping the hatch complete apart from the spoiler .

[2000zx3sct]

Front and Rear Seats Sold , Still have the door cards .

[2000zx3sct]

Adding the SVT header and Flex pipe with the borla exhaust , unfortunately no CAT as I will be needing it for my car , but for the exhaust header and flex pipe I'm asking $375 Firm .

[2000zx3sct]

Trades always welcome

[Teebs]

Do you have the SVT front brake caliper brackets? Don't need the calipers...

Thanks.

[2000zx3sct]

Yeah not going to separate at this time .

[2000zx3sct]

(07-06-2015, 03:37 PM)2000zx3sct Wrote: M

---

Have a four door red Svt I picked up for the motor and trans . It had a couple of aftermarket goodies on it . No front bumper . Have a lot of parts laying around  , some unlisted if you want anything that I don't have listed let me know . Open to trades as well . I'll try to post as many pictures as I can if you want any detailed pictures pm me.  I'm located in Hamilton            

---

1. AEM cold air intake - $100 OBO ***SOLD
Headlights in picture below - SOLD

---

2. Enkie 17inch wheels - tires need to be replaced updated price - $250 - ****SOLD

---

3. Full Interior front and rear seats ****SOLD , DOOR PANELS STILL*****SOLD

---

4. Silver HVAC controls - $25 - ****SOLD

---

5. Tail lights - $20 have 3 sets available . 

---

6. 3 good Red SVT doors as seen in pictures - best offer will let go for cheap ***SOLD

---

7. Complete Rear Svt subframe for rear disc brake swap - $300 *******SOLD

---

8. Infra red SVT spoiler - $80 , Infra Red Mirrors - $60 - ****SOLD

---

9. SVT Gloss black door trim for zx5 models - $20 *****SOLD

---

10. SVT spark plug cover - $20 ***SOLD

---

11. SVT focus computer $100 

---

12. SVT OEM subwoofer - $50OBO 

---

13. SVT leather steering wheel - $50 ****SOLD

---

14. SVT leather shift boot - $15 **** SOLD

---

15. SAP Spoiler - shadow grey - $80 ***SOLD

---

16. SAP rear bumper insert ***SOLD

[2000zx3sct]

Most of the items are sold , still have the complete front end sitting in the garage : subframe , shocks , brakes . Of course the borla exhaust , SVT header , Also just got an SVT front bumper in silver that I'm willing to part with ( had plans to put it on my wagon but I'm selling it very soon) txt if interested in anything 289-208-5361

[Teebs]

How much for the caliper and the bracket?

[2000zx3sct]

You would be getting the entire front brake setup including the knuckles . $300

[2000zx3sct]

Turns out the header is not stock SVT , it's a different design than SVT . But bolts up the same .

[Teebs]

A bit much for what I need so I'll have to pass. The brackets would bolt on to my 2000 Cougar's knuckles and allow me to move the stock calipers out to fit the 300mm SVT Focus rotors vs the stock 278mm Cougar rotors.
If you change your mind and your willing to willing to split it up, let me know.

Thanks,
Tim.

[MikkelRS]

A bit off topic, but I know the Mazda 3s 300mm caliper brackets will bolt on the same, but you will have to experiment with the spacer washers.