Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Fusion Gauges
#17
is pin 64 the correct pin? i would double check on that b4 you go cutting wires .. i'm pretty sure its right, but better safe than sorry
Below Average Car Club
Reply


Messages In This Thread
Fusion Gauges - focusnme - 09-11-2005, 12:14 PM
Fusion Gauges - 2001 ZTS - 09-11-2005, 12:24 PM
Fusion Gauges - focusnme - 09-11-2005, 12:26 PM
Fusion Gauges - OAC_Sparky - 09-11-2005, 12:29 PM
Fusion Gauges - focusnme - 09-11-2005, 12:33 PM
Fusion Gauges - 2001 ZTS - 09-11-2005, 12:37 PM
Fusion Gauges - schade - 09-11-2005, 12:37 PM
Fusion Gauges - 2001 ZTS - 09-11-2005, 12:40 PM
Fusion Gauges - hardk0re - 09-11-2005, 12:41 PM
Fusion Gauges - focusnme - 09-12-2005, 12:36 PM
Fusion Gauges - Flofocus - 09-12-2005, 12:46 PM
Fusion Gauges - focusnme - 09-12-2005, 01:20 PM
Fusion Gauges - 2001 ZTS - 09-12-2005, 01:21 PM
Fusion Gauges - Zoom - 09-12-2005, 03:09 PM
Fusion Gauges - ANTHONYD - 09-12-2005, 11:33 PM
Fusion Gauges - Zoom - 09-13-2005, 06:45 AM
Fusion Gauges - schade - 09-13-2005, 07:26 AM
Fusion Gauges - meford4u - 09-13-2005, 07:43 AM
Fusion Gauges - ANTHONYD - 09-13-2005, 07:50 AM
Fusion Gauges - focusnme - 09-13-2005, 12:12 PM
Fusion Gauges - ZX5focused - 09-13-2005, 12:27 PM
Fusion Gauges - OAC_Sparky - 09-13-2005, 01:22 PM
Fusion Gauges - Jays2000ZX3 - 09-13-2005, 01:32 PM
Fusion Gauges - dad - 09-13-2005, 03:20 PM
Fusion Gauges - crazikev - 09-13-2005, 04:19 PM
Fusion Gauges - focusnme - 09-14-2005, 09:26 PM
Fusion Gauges - focusnme - 09-16-2005, 10:20 PM
Fusion Gauges - Flofocus - 09-16-2005, 11:24 PM
Fusion Gauges - 2001 ZTS - 09-17-2005, 12:24 AM
Fusion Gauges - OAC_Sparky - 09-17-2005, 12:43 AM
Fusion Gauges - ZX5focused - 09-17-2005, 01:58 AM
Fusion Gauges - Flofocus - 09-17-2005, 02:01 AM
Fusion Gauges - ZX5focused - 09-17-2005, 02:19 AM
Fusion Gauges - meford4u - 09-17-2005, 03:56 AM
Fusion Gauges - focusnme - 09-17-2005, 09:32 AM
Fusion Gauges - ThraxXx - 09-19-2005, 09:35 PM
Fusion Gauges - ThraxXx - 09-22-2005, 04:43 AM

Forum Jump:


Users browsing this thread: 5 Guest(s)