Posts: 515
Threads: 59
Joined: May 2009
Reputation:
2
need some more help boys. I bought a Sparco 4 point cam lock racing harness from JRP during there wicked summer sale, so i got it for a pretty good price. I took about a week, week and a half to get here and when i went to pick it up low and behold its a snap in style end clip and not a bolt in style. No biggie i figure, ill just bring it home and install it, only issue is the eye bolts fit the standard seat belt thread and not the seat base or our focus style rod thing that holds the bottom of our belts up front. I went back to JRP and they said it would cost more now to get the other style.....even IF they had it....which they dont. Iv been everywhere looking to metric M10x1.5 eye bolts and i was wondering if anyone here knows of were to get them, or of another way to mount this sucker in my car lol
Posts: 219
Threads: 33
Joined: Jul 2003
Reputation:
0
Is this what you're looking for?
http://www.grainger.com/Grainger/CHICAGO...ts-_-2G736
I know it's not a local source, but if this is what you're looking for, then maybe somebody else knows where to find it in the GTA.
Ivan MacKenzie.
Old Ride: 2001 Malibu Blue MTX Street Edition Wagon
New Ride: 2010 Mocha Brown MT 2.0T Passat Wagon
Posts: 515
Threads: 59
Joined: May 2009
Reputation:
2
(09-04-2010, 03:55 AM)imack Wrote: Is this what you're looking for?
http://www.grainger.com/Grainger/CHICAGO...ts-_-2G736
I know it's not a local source, but if this is what you're looking for, then maybe somebody else knows where to find it in the GTA.
Ivan MacKenzie.
Pretty much, the only thing is it doesn't say if its forged or not, which is a must for seat applications.
Posts: 219
Threads: 33
Joined: Jul 2003
Reputation:
0
Old Ride: 2001 Malibu Blue MTX Street Edition Wagon
New Ride: 2010 Mocha Brown MT 2.0T Passat Wagon
Posts: 515
Threads: 59
Joined: May 2009
Reputation:
2
(09-04-2010, 04:36 AM)imack Wrote: You should give Brafasco (http://www.brafasco.com/locations.asp ) and Anda Tool & Fasteners (http://www.ctidirectory.com/search/compa...pany=50379) a try.
Ivan MacKenzie.
Did Brafasco, that had some but with like a 10mm shank or less, min i need is 20mm or 25mm lol. I just called fastenal and the guys looking up what they have
Posts: 1,143
Threads: 96
Joined: Dec 2003
Reputation:
0
Don't know if you found the eye bolts, but this is an alternative
Schroth Racing
Below Average Car Club
Posts: 4,124
Threads: 162
Joined: Mar 2005
Reputation:
2
Go to http://www.acklandsgrainger.com. Search up part number GRTBS10M. Its on page 1582 of their 2010 catalogue (bottom right corner). Made by Gray Tools.
Usually they have them stock in Richmond Hill warehouse and may be one day delivery to your nearest store. There is lots of stores in the GTA.
They show a list cost of 12.11ea, but they should be able to bring that down quite a bit (least 30-40%) for a walk in customer.
Sold: 2001 SE 2.0L SPI w/60mm TB, Steeda Shorty Intake.
Active: 2007 SES Hatch, Motegi MR7 Rims with 215/45ZR17 Michelin Pilot Super Sport Tires, debadged, black painted calipers and drums, RS Knob, CFM Short Throw, Billet E-Brake, CFM Focus pedals, MBRP Exhaust, XCal2, FS Front and Rear Strut Tower Bars, Diamond Plate Floor Mats and Sills, Alpine MP3 Deck, Alpine V-Power 300w Amp, Pioneer IMPP Sub, AlpineType-S door speakers, VF Engineering Rear Motor Mount, F2 RS Spoiler, Tokico D-spec shocks, HTP Cross Brace, EBC Rotors, Hawk HPS Pads, Russell SS Brake Lines, RS Wheel, SVT Blue Seats, Vibrant 2.5" Race Highflow Cat, CFM UDP. Rear SVT bumper to come.
Active: 2005 Jeep Wrangler Unlimited TJ [LJ], Volant CAI, 32" BFG Mud Terrains, and a whole bunch of goodies. 
Posts: 515
Threads: 59
Joined: May 2009
Reputation:
2
(10-05-2010, 11:32 AM)Oscar The Grouch Wrote: Go to http://www.acklandsgrainger.com. Search up part number GRTBS10M. Its on page 1582 of their 2010 catalogue (bottom right corner). Made by Gray Tools.
Usually they have them stock in Richmond Hill warehouse and may be one day delivery to your nearest store. There is lots of stores in the GTA.
They show a list cost of 12.11ea, but they should be able to bring that down quite a bit (least 30-40%) for a walk in customer.
it reads 5/16 pitch and our seat bolts are either M10 and M8 i believe, either way, Fastenal had what i needed....suppose i should post pics eh? lol
|
Hi, Guest
