[mpcv2000]

Installing this....










This should be easy does it... B)

[ANTHONYD]

Nice!

[habmann]

Nice subtle change. Definate improvement over the stock ones.

[mpcv2000]

I found them on Ebay and I thought it will be a nice add on..

[SL8RZZX3]

Looking good! can't wait to see pics of them in!

i was lazy and got these a few years back.....



pics of them in


not sure if the guy i got them from makes them any more though :(

[Flofocus]

Steeda here....

[mpcv2000]

Are they slippery when you feet are wet.. ?



My next buy will be this :







Ford doesn't make them for the Focus but someone is making a exact copy of the OEM patern and it comes with the braket and hardware .

[Flofocus]

no, the little rubber knobs really help when its wet out.

[mpcv2000]

Flofocus,Mar 22 2006, 06:54 PM Wrote:no, the little rubber knobs really help when its wet out.
[right][snapback]176457[/snapback][/right]

I sure they thought about it before us.... ;)




Ok time to eat and put these pedals on... :)

[SVT ZX3]

mpcv2000,Mar 22 2006, 04:35 PM Wrote:Are they slippery when you feet are wet.. ?
[right][snapback]176453[/snapback][/right]

Not too bad, but there is some slipping...

mpcv2000,Mar 22 2006, 04:35 PM Wrote:Ford doesn't make them for the Focus but someone is making a exact copy of the OEM patern and it comes with the braket and hardware .
[right][snapback]176453[/snapback][/right]

Redline Tuning sells this kit, if you look, you will see the dead pedal knobs are a bit more oval compared to the SVT pedals which are exactly round. Not an exact match, but close enough that no one will notice unless you told them.

[meford4u]

After they have been on for a while the rubber fades away and slppery peadle is definately what you get. Just think about replacing them every 50,000 kms.

[mpcv2000]

....Still working on it but I'm done for tonight..


I did the same thing in my Mustang and it was a pain...but now since I know , it's a bigger pain...I don't know if any of you did the SVT pedal thing but you need a lot of patience.



Stock looking....bah... :








after a lot of fighting they went it..... :angry:








For the gaz pedal I have to remove 3 nuts and I need a long 10mm 1/4 drive socket that I don't have so tomorrow is socket shopping.







To give me more room while messing with the gaz pedal I "zipptied" the throttle body wide open to free up some throttle cable including my own safety feature...just in case... ;)

[01-yellow-ZX3]

Flofocus,Mar 22 2006, 04:30 PM Wrote:Steeda here....


[right][snapback]176451[/snapback][/right]

Hey, did I ever tell you those were upside down? :P :P

[mpcv2000]

Done. All I needed was the 10mm long socket.



Looks good , I like it. Now my car will go faster... :P

[habmann]

Looks good, maybe i'll get a set to replace the steeda ones i have right now.

[dBlast]

01-yellow-ZX3,Mar 22 2006 Wrote:

Flofocus,Mar 22 2006, 04:30 PM Wrote:Steeda here....


[right][snapback]176451[/snapback][/right]

Hey, did I ever tell you those were upside down? :P :P
[right][snapback]176515[/snapback][/right]

That's the way mine are installed as well (installed by Steeda while they were doing other stuff there.)

That's the way they are oriented on their web site as well:



:iono:

[darkpuppet]

mpcv2000,Mar 22 2006, 08:25 PM Wrote:

[right][snapback]176484[/snapback][/right]

get a grommet on that power cable!!!

[mpcv2000]

darkpuppet,Mar 24 2006, 12:24 PM Wrote:get a grommet on that power cable!!!
[right][snapback]176742[/snapback][/right]

From this side you can't see but I have some loom going thru the fire wall , I know it's not a grommet but it's all I had back then.

[Flofocus]

01-yellow-ZX3,Mar 22 2006 Wrote:Hey, did I ever tell you those were upside down?  :P  :P
[right][snapback]176515[/snapback][/right]

They aren't. :P

[euro]

SVT pedal kit is really nice and sheap. I'll do mine next summer, right now I need horse power.