11-29-2012, 10:16 AM
So another update , bumper is repaired fully , and the following are pics of my repair.
![[Image: a3wy1.jpg]](http://i45.tinypic.com/a3wy1.jpg)
This was the worst repair on the thing , as it was a pressure joint , so it deserved a little more attention. so in the back looks ugly, but the front looks good.
![[Image: 23kyuzq.jpg]](http://i48.tinypic.com/23kyuzq.jpg)
this was a simple matter of reinforcing the crack which is not a supporting crack , but it is repaired and reinforced.
![[Image: 123mn1t.jpg]](http://i45.tinypic.com/123mn1t.jpg)
Some more of the reinforcement and repair
![[Image: c288i.jpg]](http://i48.tinypic.com/c288i.jpg)
some more reinforcement
![[Image: 30tjchu.jpg]](http://i50.tinypic.com/30tjchu.jpg)
the front facing side of the first image , the major repair crack.
![[Image: 2cr944h.jpg]](http://i46.tinypic.com/2cr944h.jpg)
This is after today , 1st coat of white finally went on , after a few bouts of primer and wet sand to smooth it.
![[Image: 20h24qe.jpg]](http://i46.tinypic.com/20h24qe.jpg)
![[Image: jg0f81.jpg]](http://i47.tinypic.com/jg0f81.jpg)
Tomorrow a little wet sand for a little over spray , then another coat of white . and wetsand , then clear coat.
keep in mind i am also doing this when it is far too cold to be doing this. i am baking the bumper useing a heat gun ...... not the best way to do this. but since i am in a competition with father time , and mother nature .
i want this on for the winter.
So thats where i am at. when i have the clear coat on and the lip and grill oni will take a few more pictures to show.
![[Image: a3wy1.jpg]](http://i45.tinypic.com/a3wy1.jpg)
This was the worst repair on the thing , as it was a pressure joint , so it deserved a little more attention. so in the back looks ugly, but the front looks good.
![[Image: 23kyuzq.jpg]](http://i48.tinypic.com/23kyuzq.jpg)
this was a simple matter of reinforcing the crack which is not a supporting crack , but it is repaired and reinforced.
![[Image: 123mn1t.jpg]](http://i45.tinypic.com/123mn1t.jpg)
Some more of the reinforcement and repair
![[Image: c288i.jpg]](http://i48.tinypic.com/c288i.jpg)
some more reinforcement
![[Image: 30tjchu.jpg]](http://i50.tinypic.com/30tjchu.jpg)
the front facing side of the first image , the major repair crack.
![[Image: 2cr944h.jpg]](http://i46.tinypic.com/2cr944h.jpg)
This is after today , 1st coat of white finally went on , after a few bouts of primer and wet sand to smooth it.
![[Image: 20h24qe.jpg]](http://i46.tinypic.com/20h24qe.jpg)
![[Image: jg0f81.jpg]](http://i47.tinypic.com/jg0f81.jpg)
Tomorrow a little wet sand for a little over spray , then another coat of white . and wetsand , then clear coat.
keep in mind i am also doing this when it is far too cold to be doing this. i am baking the bumper useing a heat gun ...... not the best way to do this. but since i am in a competition with father time , and mother nature .
i want this on for the winter.
So thats where i am at. when i have the clear coat on and the lip and grill oni will take a few more pictures to show.