Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Sunroof
#1
Question 
The sunroof is acting up. Have to hold and let go of button just right to get the roof to open or close properly either tilting or opening all the way up and closing. Could be switch or out of alignment? Any fix for this? Thanks.
Old enough to know me limit, yet young enough to exceed it.
Reply
#2
Check the tracks, there might be something on them not letting it open or close properly. Happened to me before
Currently - 2014 GMC Sierra 1500 SLE 4X4 Work Truck. Needs a Super Charger
2012 F150 Eco Boost Work Truck < Died several times and now it's some farmer problem.
No Longer Sleeping/In Surgery Having A Heart Transplant - 2005 Focus ZX5 Sonic Blue Modified
Sold - 1992 Astro Van CS Sky Blue Stock
Sold - 1994 Excel 2DR HB Teal First Car

Reply
#3
Not sure if your car has this, but my 2009 has a feature to "re-adjust" the sunroof by holding the buttons down. I forget the sequence, but it's in the manual.
2009 Focus SES Black Sedan Mods:

FSWerks CAI / F2 Header (non-fouler mod) custom flex / 2.5" FSwerks Stealth Stainless exhaust / FSWerks X3 tune / Autolite 104's / Steeda Strut Tower Bar / FRPP 1.5" drop / FSWerks FLS Bar / H&R 24mm RSB / MOOG endlinks / AEM wideband AFR gauge / 8000K HID Bi-xenon 55W / Tint / 17" Ford Racing Rally Wheels in Black / Coupe tails / Black grille

124whp/129wtq
Reply
#4
Thanks. I'll give it a look.
Old enough to know me limit, yet young enough to exceed it.
Reply
#5
Roof Opening Panel Motor Initialization

Updating Roof Opening Panel Motor Initialization

WARNING: The roof opening panel anti-trap function will not operate during the updating roof opening panel motor initialization procedure. Make sure that the roof opening panel opening is free of all foreign material. Failure to follow this instruction may result in personal injury.

NOTE: This procedure should only be carried out when the roof opening panel motor has not been disconnected.

NOTE: The roof opening panel alignment must be carried out prior to carrying out roof opening panel motor initialization. For additional information, refer to Roof Opening Panel Alignment in this section.

Operate the roof opening panel control switch to the up/close position until the roof opening panel is in the fully open/vent position.
Release the roof opening panel control switch.
Operate the roof opening panel control switch to the up/close position and hold for 30 seconds until there is a small movement (approximately 2 mm) and the roof opening panel motor stops.
Release the roof opening panel control switch.
Operate the roof opening panel control switch to the up/close position again within 0.5 seconds until the roof opening panel stops (one complete cycle).

Initial Roof Opening Panel Motor Initialization

WARNING: The roof opening panel anti-trap function will not operate during the updating roof opening panel motor initialization procedure. Make sure that the roof opening panel opening is free of all foreign material. Failure to follow this instruction may result in personal injury.

NOTE: This procedure must be carried out when installing any roof opening panel motor or roof opening panel.

NOTE: The roof opening panel alignment must be carried out prior to carrying out roof opening panel motor initialization. For additional information, refer to Roof Opening Panel Alignment in this section.

Operate the roof opening panel control switch to the up/close position.
Release the roof opening panel control switch.
Operate the roof opening panel control switch to the up/close position again within 0.5 seconds until the roof opening panel stops (one complete cycle).

Erasing Roof Opening Panel Motor Initialization

NOTE: The erasing procedure is to be carried out only when the roof opening panel motor has been detached from the roof opening panel.

NOTE: This procedure must be carried out before installing a previously used roof opening panel motor.

Connect the roof opening panel motor electrical connector.
Operate the roof opening panel control switch to the up/close position until the roof opening panel motor stops.
Release the roof opening panel control switch.
Operate the roof opening panel control switch again to the up/close position and hold for 30 seconds. With the roof opening panel control switch held, the roof opening panel motor will rotate in one direction.
Release the roof opening panel control switch.
Operate the roof opening panel control switch to the down/open position. If the roof opening panel motor does not rotate, the erasing procedure has been carried out successfully.
If the roof opening panel motor rotates (with the roof opening panel control switch in the down/open position), repeat the procedure.
TEAM PITA: Don't settle for a wannabe, only accept the real deal.
*Magnetic Metallic 2015 Focus ST* *Red Candy Metallic 2012 F150 SuperCrew*
*Supercharged Roush Phase 2 Kona Blue 2012 Mustang GT*
Reply
#6
Very Detailed Big Grin
Currently - 2014 GMC Sierra 1500 SLE 4X4 Work Truck. Needs a Super Charger
2012 F150 Eco Boost Work Truck < Died several times and now it's some farmer problem.
No Longer Sleeping/In Surgery Having A Heart Transplant - 2005 Focus ZX5 Sonic Blue Modified
Sold - 1992 Astro Van CS Sky Blue Stock
Sold - 1994 Excel 2DR HB Teal First Car

Reply
#7
(08-19-2010, 01:46 AM)OAC_Sparky Wrote: Roof Opening Panel Motor Initialization

Thanks Sparky. I'm on afternoons so I'll have to wait until the weekend to try this out, unless I let the wife use the Marauder Confused .
Old enough to know me limit, yet young enough to exceed it.
Reply
#8
Works normally now, thanks!
Old enough to know me limit, yet young enough to exceed it.
Reply


Forum Jump:


Users browsing this thread: 4 Guest(s)