Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Rev Limiter
#1
hey, i was just wondering what the rev limiter on the focus is, and when does it start to red line?
04 Silver ZX3, 17" Focal wheels, cold air intake,[COLOR=blue]
Reply
#2
The stock rev limiter is 6800, and redline is 7000.
Reply
#3
is it possible for valves to hit pistons when u hit the limiter?
04 Silver ZX3, 17" Focal wheels, cold air intake,[COLOR=blue]
Reply
#4
The rev limiter just cuts off fuel to the engine.
I bought a red car, because everyone knows red is the fastest.
Reply
#5
ZX3Blake,Jun 20 2005, 04:31 AM Wrote:is it possible for valves to hit pistons when u hit the limiter?
[right][snapback]115561[/snapback][/right]


No. The Focus is a non interference motor.
TEAM PITA Don't settle for a wannabe, only accept the real deal.

One day I will rule the world. For now, I have to settle for this place.
Reply
#6
meford4u,Jun 20 2005, 08:17 AM Wrote:
ZX3Blake,Jun 20 2005, 04:31 AM Wrote:is it possible for valves to hit pistons when u hit the limiter?
[right][snapback]115561[/snapback][/right]


No. The Focus is a non interference motor.
[right][snapback]115585[/snapback][/right]


They make these cars for Grandmas and soccer moms ..... there is no way to make the valves hit the pistons. :lol:
Reply
#7
Except on the SVT. Redline is i believe 7300 rpm, Limiter 7250. people have it safley pulling to 7800 with stock internals.
05 Altima SE-R
98 Grand Cherokee 5.9: Flowmaster; K&N
05 300C 5.7: Sold
99 Civic SIR: Sold
03 Focus SVT: Sold
01 Focus ZX3: Sold
Reply
#8
No way for piston's to hit valves eh.... Ats not good information for me to know lol :blink:
2000 ZX3
Reply
#9
ZX3Blake,Jun 19 2005, 11:49 PM Wrote:hey, i was just wondering what the rev limiter on the focus is, and when does it start to red line?
[right][snapback]115534[/snapback][/right]


I hit my rev liimter all the time and it doesn't do a thing to the car
Reply
#10
Remind me to test that tomorrow with the SPI :D
Daily driver 1: 2007 Jeep Wrangler Unlimited Sport "S"

33" BFG Mud-Terrain KM2s, lots of Rough Country gear - bumper, 2.5" lift, swaybar disconnects, Superwinch 10,000lb winch, Detroit Locker in rear D44 axle, custom exhaust, K+N filtercharger, Superchips-tuned.

Daily driver 2: 2006 Subaru Legacy GT

COBB Stage 1+ package - AccessPort tuner, COBB intake and airbox. Stage 2 coming shortly - COBB 3" AT stainless DP and race cat, custom 3" Magnaflow-based exhaust and Stage 2 COBB tune.
Reply
#11
break a timing belt and i'm sure you'll see the valves hit the pistons
Below Average Car Club
Reply
#12
Mason,Jun 20 2005, 10:38 AM Wrote:No was for piston's to hit valves eh.... Ats not good information for me to know lol :blink:
[right][snapback]115627[/snapback][/right]


:1engrishsign: :speakenglish:
Reply
#13
ANTHONYD,Jun 21 2005, 08:41 AM Wrote:
Mason,Jun 20 2005, 10:38 AM Wrote:No was for piston's to hit valves eh.... Ats not good information for me to know lol :blink:
[right][snapback]115627[/snapback][/right]


:1engrishsign: :speakenglish:
[right][snapback]115835[/snapback][/right]

:lol:
05 Altima SE-R
98 Grand Cherokee 5.9: Flowmaster; K&N
05 300C 5.7: Sold
99 Civic SIR: Sold
03 Focus SVT: Sold
01 Focus ZX3: Sold
Reply
#14
schade,Jun 20 2005, 10:10 PM Wrote:break a timing belt and i'm sure you'll see the valves hit the pistons
[right][snapback]115781[/snapback][/right]


No belt for me !!!! The ST uses a chain as far as i know
2005 ZX4 SOLD! ST; 1992 Mustang 5.0L S/C

[Image: lakemitchellsml.jpg][Image: burnout1sml.jpg]
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)